Gunwerks6IX
.30 Cal / 7.62mm suppressor · Gunwerks Tru-Mount Taper interface · specs and compatibility from the manufacturer
Notable features
- TBAC Summit Tested
- Sealed
Where to buy
Prices update nightly
EuroOptic
Shop links go to retailer sites; we may earn a commission. Prices shown as of our last check and may differ at checkout.
length
6.18″
weight
10.9oz
MSRP
$695
length
6.18″
weight
10.9oz
calibers
5.56–.30
material
Steel
interface
Gunwerks Tru-Mount Taper
MSRP
$695
Photos
Image: Gunwerks
- Overall length
- 6.18″
- Class
- .30 Cal / 7.62mm
- n
- 646
- Range
- 2.5″–14″
- Median
- 7.2″
- Diameter
- 1.48″
- Class
- .30 Cal / 7.62mm
- n
- 617
- Range
- 1.36″–2.74″
- Median
- 1.62″
- Weight
- 10.9 oz
- Material
- Hardened 17-4 Stainless Steel
- Finish / treatment
- Matte Black High Temperature Cerakote, High-Temp Cerakote
- Max caliber
- .30 Cal / 7.62mm
- Base interface
- Gunwerks Tru-Mount Taper
- Maintenance
- Sealed (not user serviceable)
- MSRP
- $695
- Class
- .30 Cal / 7.62mm
- n
- 574
- Range
- $199–$2,380
- Median
- $990
Shorter than most .30 Cal / 7.62mm suppressors
Length compared against the 646 .30 Cal / 7.62mm suppressors in the catalog that publish one. Quartile basis; a value inside the middle half carries no note.
Narrower than most .30 Cal / 7.62mm suppressors
Diameter compared against the 617 .30 Cal / 7.62mm suppressors in the catalog that publish one. Quartile basis; a value inside the middle half carries no note.
Cheaper than most .30 Cal / 7.62mm suppressors
MSRP compared against the 574 .30 Cal / 7.62mm suppressors in the catalog that publish one. Quartile basis; a value inside the middle half carries no note.
Prices are manufacturer's suggested retail (MSRP). What you pay may differ.
Is something on this page wrong?
- Base interface
- Gunwerks Tru-Mount Taper
This suppressor uses Gunwerks's proprietary Gunwerks Tru-Mount Taper: 6 mounts in our catalog fit it, all from Gunwerks. Plan on buying mounting hardware from Gunwerks.
Which ones fit your barrel and host?
Check in the BuilderThe Thunder Beast Silencer Summit fires every suppressor entered on the same gun, with the same equipment. 6IX was measured in 1 test. Figures can only be compared with others from the same test, so each one links to everything else fired on that gun.
Bolt-action and lever rifles
Measurements published by Thunder Beast Arms Corp. How to read these
Manufacturer claim
- Engineered around reliable, repeatable performance on precision rifles: minimal point of impact shift, and no loss of a rifle’s ability to print tight groups.
- Suppressor design optimized for sound suppression and performance on modern magnum hunting cartridges rather than around the 5.56 and 7.62 military rounds the industry standard is built on.
- Weighs 12.4 oz including the thread adapter and reducer.
- Tubeless, fully welded body rather than a tube-and-baffle stack held by an outer sleeve, which keeps weight down and removes a snag edge for brush, scabbards, and cases.
Show all 10 ▾ ▴
- The Tru-Mount taper seats ahead of the threads so combustion residue is less likely to lock the mount in place. Hex-key geometry in the adapter bore and machined wrench flats on the suppressor allow a 3/8" Allen wrench and a crescent wrench to separate a stuck mount without specialized tools.
- Material: Hardened 17-4 Stainless Steel.
- Finish: Matte Black - High Temperature Cerakote.
- Designed and optimized for modern cartridges in the 6.5mm to 30 caliber range, with caliber-specific bore reducers available for further fine-tuning.
- Tapered thread adapter: 1/2x28 and 5/8x24 included. Bore Reducers: 30 caliber included, additional reducers available for 6mm, 6.5mm and 7mm.
- In the box: the serialized suppressor, 1/2x28 and 5/8x24 Tru-Mount thread adapters, a .30-caliber ReducR, and the owner’s manual. Additional thread pitches and bore reducers are sold separately.
Is one of these wrong, or does our wording say something the source doesn't?
